| WoodsBuggy.com http://woodsbuggy.com/phpBB3/ |
|
| I need ball joint spindles http://woodsbuggy.com/phpBB3/viewtopic.php?f=7&t=2850 |
Page 1 of 1 |
| Author: | travisdunebuggy [ Tue Jan 29, 2008 8:55 am ] |
| Post subject: | I need ball joint spindles |
Im tryn to ma ke a set of raised spindles i have one need another set just need from ball joint out just the spindles i have some link pin stuff(stock) that some one might be interested in tradeing for spindles!!  you might already have some raised spindles let me know we can work out somthing thanks!!
|
|
| Author: | The Wild Kids [ Tue Jan 29, 2008 9:05 am ] |
| Post subject: | |
Travis, Call Larry at the Speedshop in Harriman. 865-882-0093 The Wild Kids |
|
| Author: | chris38375 [ Tue Jan 29, 2008 9:13 am ] |
| Post subject: | |
empi sells jus the spindle so u dont have to cut any down i think there called spuds,for a ball joint |
|
| Author: | travisdunebuggy [ Tue Jan 29, 2008 9:17 am ] |
| Post subject: | |
[quote='chris38375']empi sells jus the spindle so u dont have to cut any down i think there called spuds,for a ball joint[/quote]Well im goin through my motor and im not gettn to work like i need to so the funds are a little low so i gotta go as cheap as i can or i would just buy some!!! |
|
| Author: | The Wild Kids [ Tue Jan 29, 2008 9:23 am ] |
| Post subject: | |
Larry might have a good set of used ones that will save on the wallet some. Just a thought The Wild Kids |
|
| Author: | travisdunebuggy [ Tue Jan 29, 2008 9:34 am ] |
| Post subject: | |
[quote='chris38375']empi sells jus the spindle so u dont have to cut any down i think there called spuds,for a ball joint[/quote]I looked up the spuds but not the route i was wanting to take a guy showed me how to cut the 2 and make one looks a lot stronger than the spuds!! |
|
| Author: | travisdunebuggy [ Tue Jan 29, 2008 9:38 am ] |
| Post subject: | |
[quote='The Wild Kids']Larry might have a good set of used ones that will save on the wallet some. Just a thought The Wild Kids[/quote]How is he about tradeing ?????
|
|
| Author: | travisdunebuggy [ Tue Jan 29, 2008 9:50 am ] |
| Post subject: | |
[quote='travisdunebuggy'][quote='chris38375']empi sells jus the spindle so u dont have to cut any down i think there called spuds,for a ball joint[/quote]Well im goin through my motor and im not gettn to work like i need to so the funds are a little low so i gotta go as cheap as i can or i would just buy some!!![/quote]Go to blindchickenracing.com look at the raised spindles you'll see what im tryn to do !! |
|
| Author: | The Wild Kids [ Tue Jan 29, 2008 4:52 pm ] |
| Post subject: | |
He will trade but it depends on what you have really. Best bet is to call and ask him. He is one of the best that I know of. The Wild Kids |
|
| Author: | bruce 1 [ Tue Jan 29, 2008 7:45 pm ] |
| Post subject: | |
I have a B/J beam spindle to spindle, With raised spindles on it that larry at the speed shop built, and installed. What do you have to trade????? The beam is adjustable also. I live in Chatsworth ga. Make me an offer. |
|
| Author: | travisdunebuggy [ Tue Jan 29, 2008 8:31 pm ] |
| Post subject: | |
[quote='bruce 1']I have a B/J beam spindle to spindle, With raised spindles on it that larry at the speed shop built, and installed. What do you have to trade????? The beam is adjustable also. I live in Chatsworth ga. Make me an offer.[/quote]How much are they raised ?? i have some linkpin front end i think one is spindle to spindle no back plates 69mm crank with rods cam and brass gear real good shape ;big 5 15x15 on old set of fire stones but not much tread i would prob need you |
|
| Author: | bruce 1 [ Wed Jan 30, 2008 10:53 pm ] |
| Post subject: | |
|
|
| Author: | travisdunebuggy [ Wed Jan 30, 2008 11:35 pm ] |
| Post subject: | front end |
Ill be over tomorrow to get it |
|
| Author: | travisdunebuggy [ Mon Feb 04, 2008 1:03 am ] |
| Post subject: | spindles |
Can any one tell me why my ball joint spindles are smaller than the ones on my new raised frontend there both balljoint frontends??????????????
|
|
| Author: | FOX SHOX [ Mon Feb 04, 2008 7:04 am ] |
| Post subject: | |
I believe there were 2 years of ball joint front ends?? The 5 lug and the 4 lug. I think that the inside bearing(by the brakes) are smaller and the out side(bt the lock nut) is the same size?? Did a drum swap on a buggy from 5 lug to 4 lug and had to change the bearings and seals. Thanks Dave T |
|
| Author: | Roy [ Mon Feb 04, 2008 8:18 am ] |
| Post subject: | |
66 and 67 were early ball joint. 68 and up were late ball joint. |
|
| Author: | travisdunebuggy [ Mon Feb 04, 2008 11:26 am ] |
| Post subject: | which year has the big spindles |
[quote='dave t']I believe there were 2 years of ball joint front ends?? The 5 lug and the 4 lug. I think that the inside bearing(by the brakes) are smaller and the out side(bt the lock nut) is the same size?? Did a drum swap on a buggy from 5 lug to 4 lug and had to change the bearings and seals. Thanks Dave T[/quote]So does this mean that i just need new bearins or will i need to get new hubs also??????
|
|
| Author: | turboblue [ Mon Feb 04, 2008 2:30 pm ] |
| Post subject: | |
The inner bearing is smaller on the 5 lug drums and the earlier 4 lug versions. They were that way through 68 and part of 69. Early part number is 311 405 625. Inner spindle diameter is about 1-1/16" Seal # is 131 405 641A Late part number is 311 405 625B Inner spindle diameter is about 1-1/8" Seal # is 111 405 641B Outside bearings are all the same. You can install b/j 5 lug drums on the late spindles by using the appropriate late inner bearing and seal. Or late drums on the early b/j spindles with the right bearings/seals too. |
|
| Author: | travisdunebuggy [ Mon Feb 04, 2008 11:50 pm ] |
| Post subject: | spindles |
Cool i didnt know that thanks guys ive learned a lot !!! 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|