| WoodsBuggy.com http://woodsbuggy.com/phpBB3/ |
|
| tiking http://woodsbuggy.com/phpBB3/viewtopic.php?f=3&t=3091 |
Page 1 of 2 |
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 10:51 pm ] |
| Post subject: | tiking |
my motor is ticking. its almost the same sound i had last winter. last winter i sherred the dial pins off my crank. but we checked it and my flywheel was tight. any idea on what i could be in trouble for? its just a stock motor and the only upgrade is a 2 barrel. thanks guys, dave |
|
| Author: | davehix [ Mon Feb 18, 2008 10:59 pm ] |
| Post subject: | |
check the valves? adjust them see if it helps. |
|
| Author: | purplerail [ Mon Feb 18, 2008 11:06 pm ] |
| Post subject: | |
knock? |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:09 pm ] |
| Post subject: | |
2 of my rockers are looseone i dont think is adjusted right but the one i can move it about a 1/4 side to side. i dont think thats normal. right? |
|
| Author: | J.DiNapoli [ Mon Feb 18, 2008 11:18 pm ] |
| Post subject: | |
do you run stock rockers? if so you probably broke spring washer. its the wavy one. |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:23 pm ] |
| Post subject: | |
ya stock. it just seems to be the rocker. ill check in a sec and post |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:26 pm ] |
| Post subject: | |
the spring n washer are fine. just i can move the rocker waayyyy to far. all my other ones are solid. |
|
| Author: | J.DiNapoli [ Mon Feb 18, 2008 11:35 pm ] |
| Post subject: | |
you have your rocker, on either side is a flat washer,then spring washer then flat washer.you should have a gap between flat washers where spring washer is.it could be cracked.i have had this happen to me a couple of times. |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:38 pm ] |
| Post subject: | |
theres a huge fckin space on each side if the rocker |
|
| Author: | buggy66 [ Mon Feb 18, 2008 11:42 pm ] |
| Post subject: | |
Did you break a clip? |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:46 pm ] |
| Post subject: | |
i dont know much about motors. can you explain |
|
| Author: | J.DiNapoli [ Mon Feb 18, 2008 11:46 pm ] |
| Post subject: | |
yea check your clips |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:53 pm ] |
| Post subject: | |
clips? |
|
| Author: | frankenbuggy06 [ Mon Feb 18, 2008 11:59 pm ] |
| Post subject: | |
i see the spring. on the rocker its not there on the loose one. i cant find it i hope its not in the motor |
|
| Author: | J.DiNapoli [ Tue Feb 19, 2008 12:46 am ] |
| Post subject: | |
was it in your valve cover? |
|
| Author: | J.DiNapoli [ Tue Feb 19, 2008 12:48 am ] |
| Post subject: | |
the clips slide over rocker shaft and hold your rocker w/washers in place. |
|
| Author: | frankenbuggy06 [ Tue Feb 19, 2008 3:58 pm ] |
| Post subject: | |
no i didnt see anything in the valve covers. and my clip is there |
|
| Author: | J.DiNapoli [ Tue Feb 19, 2008 6:41 pm ] |
| Post subject: | |
have you recently had your rocker shafts off? maybe forgot to put in on.i dont think it would pass through your pushrod tubes.but you may want to ask somebody else if they have ever ran into this. |
|
| Author: | frankenbuggy06 [ Tue Feb 19, 2008 7:49 pm ] |
| Post subject: | |
havent pulled them off. im going to pullthem off tonight when the garage heats up. its a bit chilly up in northern ohio. haha. it used to be my dads motor then the bastard upgraded. haah. but i work with what i got. i wanna put some 1.25 ratio rockers on. help any? make a diff? plz tell experiences. if its worth it or not |
|
| Author: | FOX SHOX [ Tue Feb 19, 2008 8:26 pm ] |
| Post subject: | Busted Wavey washer |
Here is a pic of a broken wavey washer from my 1915. Found it b-4 it went into oil pan.[img][img]http://i119.photobucket.com/albums/o157/silversandoffroad/IMG00024.jpg[/img]  This pic shows a little of what the rockers and shafts look like. Thanks Dave T  This last pic shows what happens to the non-hardened tips [/img]
|
|
| Author: | frankenbuggy06 [ Tue Feb 19, 2008 8:50 pm ] |
| Post subject: | |
1. id get me some big foot ball adjusters. thanks for the pics. were gonna pull it off tonight. ill post pics later |
|
| Author: | J.DiNapoli [ Tue Feb 19, 2008 8:58 pm ] |
| Post subject: | Re: Busted Wavey washer |
[quote='dave t']Here is a pic of a broken wavey washer from my 1915. Found it b-4 it went into oil pan.[img][img]http://i119.photobucket.com/albums/o157/silversandoffroad/IMG00024.jpg[/img] This pic shows a little of what the rockers and shafts look like. Thanks Dave T [img]http://i119.photobucket.com/albums/o157/silversandoffroad/IMG0
|
|
| Author: | buggy66 [ Tue Feb 19, 2008 9:30 pm ] |
| Post subject: | |
I hada clip break on a rocker shaft once ---It sounded to me like a rod that kept coming and going.I had a buddy pull me back to trailer. Once i figured it out I done away w/ stock shafts -went HD bolted shafts. Good luck with your problem. Mark |
|
| Author: | frankenbuggy06 [ Tue Feb 19, 2008 9:32 pm ] |
| Post subject: | |
thanks guys. i wouldnt be as far. yet alone have half as much knowledge as i do. |
|
| Author: | JeffClay [ Wed Feb 20, 2008 3:14 pm ] |
| Post subject: | |
yeah i switched to 1.25 rockers for my 1641. i had pat at LA order me autocraft ones, they have bolt ends, no clip BS. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|