Fill us in we are all friends here.
Aaron Creech wrote:
Speechless...
| WoodsBuggy.com http://woodsbuggy.com/phpBB3/ |
|
| Looking to buy some new heads... http://woodsbuggy.com/phpBB3/viewtopic.php?f=3&t=14577 |
Page 1 of 1 |
| Author: | mike ball [ Wed Jan 02, 2013 9:04 am ] |
| Post subject: | Looking to buy some new heads... |
I'm looking to buy a new set of heads for my 2387 . Just wondering what i should go with ? I'm looking at going with the cb 1409 heads 044 ultra wedge ported 46x37mm what do u think? Will be only riding in the woods. |
|
| Author: | reno2165 [ Wed Jan 02, 2013 7:45 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
http://www.youtube.com/watch?v=kc5NcPjO ... detailpage im not sure i did this rite but this buggy also has a 2387 with those same ultrawedge port heads |
|
| Author: | Aaron Creech [ Wed Jan 02, 2013 8:05 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Any idea what cam and compression your gonna run? What carbs? Also how much rpm do you plan to turn this engine. Personally for a woods motor I would use a set of the CB Super Pro heads. They have alot better port velocity to help with low end torque and are still capable of producing 200HP with the right combo. |
|
| Author: | RDB#3 [ Wed Jan 02, 2013 9:47 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Im just throwing this out there....My personal preference is SuperFlow heads with the small valves, VZ25 cam...because out of all the cams available it has a (wider) power range than most cams,44 on the carbs and 1 1/2" for the exhaust,D.U.I. ignition,10.1 on the compression. Building power is one thing, just be sure to spread it out or your not going to have it somewhere along the trail. |
|
| Author: | mike ball [ Thu Jan 03, 2013 9:02 am ] |
| Post subject: | Re: Looking to buy some new heads... |
Im running a vz15 cam 10.1 compression and delordo 45 carbs wanting to turn about 6500 max rpm .. |
|
| Author: | reno2165 [ Thu Jan 03, 2013 5:04 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
mike ball wrote: Im running a vz15 cam 10.1 compression and delordo 45 carbs wanting to turn about 6500 max rpm .. the buggy in the video also runs a vz15 cam with dual dellorto 45s... his buggy easily turns 6500 and then some.. |
|
| Author: | hyde [ Thu Jan 03, 2013 7:43 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Ported S/E or 044 super pro Will make more TQ then the wedge ports or S/F . For cam I like the FK 43 with 1.4 rockers or W120 and 1.25 With the 10 to 1 and 45 carbes |
|
| Author: | Aaron Creech [ Thu Jan 03, 2013 7:57 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Speechless... |
|
| Author: | ridenrace6 [ Fri Jan 04, 2013 12:39 am ] |
| Post subject: | Re: Looking to buy some new heads... |
im with hyde and aaron on the heads, super pro or street eliminators would be my suggestion with either 42 x 37.5 or 44 x 37.5 valves, also i think you can call and get either one upgraded to the vw650 springs and titanium retainers when ordering them, its cheaper that way than having to upgrade those components a year or so later. the pro gas heads come with these upgrades but the flow rates/port work is a little different than the super pro heads |
|
| Author: | davehix [ Fri Jan 04, 2013 3:48 am ] |
| Post subject: | Re: Looking to buy some new heads... |
Fill us in we are all friends here. Aaron Creech wrote: Speechless...
|
|
| Author: | Aaron Creech [ Fri Jan 04, 2013 8:59 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Are you running ratio rockers with that cam? If you are,and plan to keep that cam combo,do yourself a favor and get the VW650 spring upgrade.There is no way that a standard dual spring can control the valve at 6500 RPM. My personal opinion is you should scrap that cam and put in something more suitable for a BIG engine with a nice set of heads. |
|
| Author: | mike ball [ Mon Jan 07, 2013 5:18 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Aaron what cam do you perfer ? I bought a set of 1458 Cylinder Heads - 044 Ultra Mag Plus (44 x 37.5mm) 94mm Bore . |
|
| Author: | Aaron Creech [ Tue Jan 08, 2013 8:27 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
With those heads I would use an Engle FK-7 or an FK-43. Both with at least 1.4 rockers.The FK-7 will be easier on the valvetrain but may give up a little torque compared to the FK-43. |
|
| Author: | hyde [ Wed Jan 09, 2013 9:27 pm ] |
| Post subject: | Re: Looking to buy some new heads... |
Aaron Creech wrote: With those heads I would use an Engle FK-7 or an FK-43. Both with at least 1.4 rockers.The FK-7 will be easier on the valvetrain but may give up a little torque compared to the FK-43. X2 I like the fk 42 or 43 over the fk7 for TQ and HP . I have seen 190 TQ on the dyno with a Fk 43 at 4000 rpm in a 2387 |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|