Seen a few guys run the turbos off the mistubishi eclipse,and the little dodge motors on 1641's.don't know how well they made power but seen them running them.Chad
| WoodsBuggy.com http://woodsbuggy.com/phpBB3/ |
|
| compression ratio 1641 http://woodsbuggy.com/phpBB3/viewtopic.php?f=3&t=13137 |
Page 1 of 1 |
| Author: | tcn1989 [ Thu Feb 09, 2012 12:05 am ] |
| Post subject: | compression ratio 1641 |
How do i change the compression ratio on my single port 1641 i will be running this turbo T3/T4 4 BOLT T04E A/R.63 WET FLOAT BEARING TURBOCHARGER+8 PSI INTERNAL WASTEGATE with a bov and manual adjustable boost controller what compression ratio do i want to be at |
|
| Author: | streetstock174 [ Thu Feb 09, 2012 1:20 am ] |
| Post subject: | Re: compression ratio 1641 |
You change the compression ratio by adding shims in between the jugs and the block. More shim, less compression. I think with a turbo motor, 9 to 1 or so? |
|
| Author: | tcn1989 [ Thu Feb 09, 2012 1:23 am ] |
| Post subject: | Re: compression ratio 1641 |
thanks for the info are there different size shims. what is the compression of a stock 1641 single port |
|
| Author: | streetstock174 [ Thu Feb 09, 2012 1:29 am ] |
| Post subject: | Re: compression ratio 1641 |
Yes there are different size shims, I think 0.015 and 0.030 at a minimum. No clue on the stock compression, probably 8 to 1 or so? |
|
| Author: | Aaron Creech [ Thu Feb 09, 2012 1:30 am ] |
| Post subject: | Re: compression ratio 1641 |
To know your compression ratio you need to know what the deck height is and what cc the combustion chambers in the heads are. If your heads are uncut I would guess that your compression would MAYBE be 7.5:1. You could get away with a little more than that as long as it was tuned good and the timing was kept in check. Good fuel is a must as well. Also that is a pretty big turbo for a little bitty 1641,you will really need to wring its guts out to get it to make boost. |
|
| Author: | tcn1989 [ Thu Feb 09, 2012 1:40 am ] |
| Post subject: | Re: compression ratio 1641 |
what would be a turbo size to run |
|
| Author: | hyde [ Thu Feb 09, 2012 8:01 pm ] |
| Post subject: | Re: compression ratio 1641 |
1.6 L is 1600cc . Find a turbo off a car around 1.6L . call Bill Westerfield 513-367-2835 HE built some stock 1600 with stock turbos 20 year ago. |
|
| Author: | gasman [ Thu Feb 09, 2012 8:22 pm ] |
| Post subject: | Re: compression ratio 1641 |
Seen a few guys run the turbos off the mistubishi eclipse,and the little dodge motors on 1641's.don't know how well they made power but seen them running them.Chad
|
|
| Author: | rockrockets1 [ Thu Feb 09, 2012 9:34 pm ] |
| Post subject: | Re: compression ratio 1641 |
tcn1989 wrote: How do i change the compression ratio on my single port 1641 i will be running this turbo T3/T4 4 BOLT T04E A/R.63 WET FLOAT BEARING TURBOCHARGER+8 PSI INTERNAL WASTEGATE with a bov and manual adjustable boost controller what compression ratio do i want to be at    That's funny .You kidding right
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|