Ok, got it reamed on one side. I feel like i need to beef this up a little. Or do any of you guys have any feedback on these things holding up?
| WoodsBuggy.com http://woodsbuggy.com/phpBB3/ |
|
| IH tie rod end conversion. http://woodsbuggy.com/phpBB3/viewtopic.php?f=26&t=8735 |
Page 1 of 1 |
| Author: | nitro_mudder [ Sun Feb 14, 2010 5:30 pm ] |
| Post subject: | IH tie rod end conversion. |
Where do I get a reamer? |
|
| Author: | hyde [ Sun Feb 14, 2010 7:21 pm ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
Speedwaymotors.com or goodson tools |
|
| Author: | nitro_mudder [ Sun Feb 14, 2010 8:53 pm ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
Anyone know the pitch?1.5 or 2" per foot? |
|
| Author: | aboone993 [ Mon Feb 15, 2010 12:02 am ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
bought mine at the local race shop . 1.5 |
|
| Author: | Dave Winterburn [ Wed Feb 17, 2010 11:20 pm ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
The only one I could find was from Snap-on. |
|
| Author: | nitro_mudder [ Wed Feb 17, 2010 11:27 pm ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
Got one at wholesale tool for $19 in Indianapolis |
|
| Author: | nitro_mudder [ Sun Feb 21, 2010 7:06 pm ] |
| Post subject: | Re: Need to ream my Pitman for IH, where do I get the reamer? |
Ok, got it reamed on one side. I feel like i need to beef this up a little. Or do any of you guys have any feedback on these things holding up?
|
|
| Author: | hillaholic [ Sun Feb 21, 2010 7:29 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
not mine but a good idea found it here .http://www.thesamba.com/vw/forum/viewto ... pitman+arm 
|
|
| Author: | nitro_mudder [ Sun Feb 21, 2010 7:34 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
Lol, I already traced out some steal to do just that. |
|
| Author: | kyjr.buggy1 [ Mon Feb 22, 2010 3:10 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
Woohoo! weight, weight, weight!!!   -Dakotah/koko |
|
| Author: | bruce 1 [ Mon Feb 22, 2010 7:25 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
kyjr.buggy1 wrote: Woohoo! weight, weight, weight!!! -Dakotah/koko You better look out KOKO he is putting all those EXTREME parts on his buggy. He says he is going to smack you around. |
|
| Author: | nitro_mudder [ Mon Feb 22, 2010 7:32 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
Carefull koko, weight & momentum = inertia also known as RAMMING SPEED!!!! And yep I know, I kant spel 
|
|
| Author: | nitro_mudder [ Sun Feb 28, 2010 1:49 pm ] |
| Post subject: | Re: Reamed my Pitman for IH tie rod ends. Could use some advise. |
Thanks Instigator for not letting me cut this out, lol    
|
|
| Author: | instigator [ Sun Feb 28, 2010 3:18 pm ] |
| Post subject: | Re: IH tie rod end conversion. |
that didn't turn out bad at all. no bad for being 300miles apart. |
|
| Author: | nitro_mudder [ Sun Feb 28, 2010 3:54 pm ] |
| Post subject: | Re: IH tie rod end conversion. |
I traced the arm, scanned it and e-mailed it to instigator and it still fit, lol. Thanks again Russ!!!!! |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|